Resources
How Often Should VCT Floors Be Stripped and Waxed?

Vinyl composition tile is still one of the most common floors we see in offices, clinics, schools, and retail space across Williamson and Travis Counties. The tile is sturdy. What people notice, and what actually takes the daily beating, is the finish on top of it. When that finish is intact, mopping lifts soil. When it wears through, grit works into the tile itself and the floor looks dull no matter how often it is mopped.
Facility managers in Round Rock, Georgetown, and Hutto ask us the same question: how often should these floors be stripped and waxed? There is no single calendar that fits every building. Traffic, the condition of the finish, and how the floor is maintained between projects all change the answer. The ranges below are general guidelines we use as a starting point, then adjust after we see the floor.
What the finish is doing
A VCT floor is protected by layers of floor finish. Foot traffic, grit, and chair casters wear those layers down. In Central Texas, a lot of that grit is fine limestone and caliche dust tracked in from construction sites, parking lots, and unpaved edges. Under shoes it acts like sandpaper. Summer heat keeps doors opening onto hot pavement, and a sudden storm turns entry mats into mud traps. The finish is what stands between that soil and the tile.
Nightly dust mopping and damp mopping keep the surface presentable. They do not put finish back. That is why a floor‑care plan has more than one kind of visit.
Three levels of floor care
Think of VCT care as three different jobs, not one. Each one is right at a different point in the life of the finish.
Burnishing
Burnishing is a high‑speed polish of finish that is still in good shape. It knocks down scuffs and brings the gloss back without removing the coating. It is the lightest of the three. Busy corridors may be burnished on a regular cycle, while a quiet private office may rarely need it. Burnishing cannot repair finish that has worn through to the tile.
Scrub and recoat
A scrub and recoat deep‑scrubs the top of the existing finish, removes embedded soil from that top layer, and lays down fresh coats. The old finish stays in place as a base. This is the right move when the floor is dull or scratched but the finish is still continuous, with no bare tile showing through. Many moderate‑traffic buildings live on a rhythm of scrub and recoat, and save a full strip for when the finish has actually failed.
Strip and wax
A strip and wax removes the old finish down to the tile, then applies new coats. It is the restorative step. We use it when finish is yellowed, built up in the corners, worn through in the walkways, or so embedded with soil that a scrub will not clear it. Our VCT strip and wax service follows that sequence: prep the floor, apply stripper, scrub off the old finish, and lay fresh coats so the tile is protected again.
A traffic‑based starting point
These are general guidelines, not a schedule we assign sight unseen. Soil level, matting, and how the nightly crew mops all move the date.
- Low traffic. Private offices, small professional suites, and lightly used conference wings. A full strip and wax about once a year is a common starting point, with burnishing only if scuffs build up. Some of these floors go longer if mats are good and the finish was applied well.
- Moderate traffic. Open offices, medical and dental suites, and apartment leasing offices. Many of these floors are stripped and waxed once or twice a year, with a scrub and recoat on the main paths in between. Waiting rooms and front entries usually need attention before the rest of the suite.
- High traffic. School corridors, retail sales floors, busy lobbies, and clinic halls. A full strip more than once a year is common, and scrub and recoat visits fill the gaps so the walkways do not go bare. Entries need their own look during rainy weeks.
- Very heavy or harsh soil. Shops that open onto gravel lots, warehouse offices next to production floors, and any door that takes caliche or job‑site dust. The finish disappears faster here. We shorten the cycle rather than waiting for the tile to stain.
A school in Georgetown and a quiet office off a side street in Taylor can have the same tile and completely different calendars. During an on‑site visit we look at the wear pattern, not the address.
What Central Texas adds to the calendar
The local climate shows up on VCT in a few predictable ways.
- Dust season is most of the year. Construction along the I‑35 corridor, from Austin through Round Rock, Hutto, and Georgetown, keeps fine grit moving. Cedar Park, Leander, and Liberty Hill pick up the same dust from new neighborhoods and caliche lots. Grit that is not stopped at the door shortens the life of the finish.
- Cedar and spring pollen. Ashe juniper pollen, which people here call cedar, is heaviest from about mid‑December through February, especially west of I‑35. It is not as abrasive as caliche, but it sticks to damp entries and makes a freshly mopped floor look dusty by noon. Pflugerville and the eastern side of the metro see it too, usually a little lighter.
- Rainy‑season mud. When storms hit, entries in every city we serve go from dry to muddy in an afternoon. Mud under a mop becomes a gray film in the finish. Good scraper mats outside and absorbent mats inside do more for the floor than an extra coat of finish.
- Long, hot months. Air conditioning runs for much of the year, and the transition at the front door is where finish scuffs first. We pay attention to that first twenty feet before we recommend a building‑wide strip.
Signs the floor needs more than mopping
- Walkways look dull while the edges of the room still have a shine.
- Black heel marks stay after mopping, or the tile color looks different in the traffic lane.
- Finish is yellow, cloudy, or thick and cracked along baseboards.
- Mopping leaves a streaky film that returns the next day.
- You can see bare tile, or the surface feels rough underhand where people turn into a hallway.
The first two often call for a scrub and recoat or a burnish. The last three usually mean it is time to strip. Catching a worn path early is easier on the tile than waiting until soil has stained it.
How a strip and wax visit is planned
Stripping is wet, slow work, and the floor cannot be walked while new finish is curing. We schedule it around your operation, often after hours or over a weekend, and we work in sections when a building cannot close all at once. Furniture is moved or left on sliders, the old finish comes off, and new coats go down. The number of coats depends on the traffic that floor will see, not on a fixed recipe we apply everywhere.
Between those visits, routine facility cleaning is what protects the investment. A nightly crew that dust‑mops grit before it is ground in, and that keeps mats straight, will make a strip last longer. If the same crew also knows which corridors are due for a burnish, the floor does not lurch from shiny to worn.
Where this fits in Williamson and Travis Counties
We refinish VCT for offices, clinics, schools, and retail floors from Austin and Round Rock out to Cedar Park, Leander, Liberty Hill, Georgetown, Hutto, Pflugerville, and Taylor. If you are comparing buildings, our notes on carpet and tile care in Central Texas dust and cedar season cover the same soil, on the other floor types you may have in the same facility.
If you want a second set of eyes on a dull lobby or a school corridor, request a free on‑site quote or call us at (512) 200‑7093. We will walk the floor with you and tell you whether it needs a burnish, a scrub and recoat, or a full strip and wax.
Frequently asked questions
How often should VCT floors be stripped and waxed?
It depends on traffic and the condition of the finish. Many low-traffic offices start at about once a year. Busier corridors, schools, and retail floors are often stripped more than once a year, with scrub and recoat visits in between. These are general guidelines, and the floor itself should decide.
What is the difference between a scrub and recoat and a strip and wax?
A scrub and recoat deep-scrubs the existing finish and adds new coats on top of it. A strip and wax removes the old finish down to the tile, then applies new coats. A scrub and recoat fits when the finish is still continuous. A strip fits when the finish is worn through, yellowed, or heavily built up.
Does burnishing replace a strip and wax?
No. Burnishing polishes finish that is still in good shape. It does not replace missing finish. If the tile is showing through in the walkways, the floor needs a scrub and recoat or a full strip, not only a burnish.

